Technical Papers

A new wafer technology, named CDS (Crystallization on Dipped Substrate), is under development and has been found to be effective in the reduction of wafer cost and silicon feedstock. CDS technology was applied to 156mm x 156mm-sized wafers, obtained via the throughput of 1825cm2/min, and the resulting cell efficiency of 14.8% was confirmed. This paper outlines the principle behind the technology and outlines the procedure.

A vast majority of silicon solar cells are manufactured using silver paste that is screen printed onto the front side of the wafer and fired to form the front-side contact. Though this method is well established within the industry, it continues to present several areas for potential efficiency improvements. The Fraunhofer Institute [1] has, among others, studied the potential of using electrodeposition of silver on top of the front side silver paste as a way to improve the front-side contact and increase cell efficiency. These results have shown cell efficiency increases of up to 0.4% absolute. This type of improvement has captured the interest of many manufacturers, but there has been a hesitancy to adopt electrodeposition as there is uncertainty as to what they can expect on their cells. Since efficiency gains are dependent upon many factors that can be unique to an individual cell, this paper provides a much-needed exploration of the potential effects of electrodeposition of silver in a way that isolates its effects from that of other factors.

Crystalline wafer and thin-film photovoltaics manufacturing have experienced dramatic expansion in recent years, but future growth requires increasingly effective strategies to reduce costs and increase the competitiveness of PV power. Reducing PV manufacturing costs has been a prime focus of the industry. In the current climate, cost reduction is especially critical given the industry shakeout that many analysts are forecasting. Now more than ever, it is important to bring manufacturing capacity online quickly and cost effectively. The vast majority of commercial-scale PV manufacturing capacity is new construction (greenfield), meaning it is purpose-built on an unused piece of land; however, there are alternatives. This paper will outline opportunities for re-use of existing obsolete semiconductor fabs, and the steps required to convert from one manufacturing strand to another.

Three buzzwords dominate the discussion about the future of the photovoltaic market in the U.S. right now: ITC (investment tax credit), credit crunch, and Obama. All three have the potential to shape how the solar industry will look in the next decades. Primary data results from EuPD Research show that after a year that featured much wailing and gnashing of teeth, market participants are now “realistically optimistic” on the prospects for the industry, despite the influence of the international credit crisis.

The continued tight supply and high cost of polysilicon, coinciding with the growth in demand for solar energy, has been a key catalyst for the rapid adoption of thin-film technologies in just the last two years. Although the technology has in development for over 15 years, it is only now that thin film has emerged as a viable low cost-per-watt alternative to conventional crystalline silicon cells. Taiwan, a powerhouse in the electronics and microelectronics industries, is also turning its attention to photovoltaics. Playing catch-up is something at which the Taiwanese have proven to be very effective, with a growing emphasis on thin film as a means to become another major centre and net exporter.

In the perpetual struggle to reduce the costs associated with PV energy generation, one aspect of the manufacturing process has potential to shine. To date, the PV sector is dominated by crystalline silicon wafers (90%), which largely use silver as the conducting medium for the front side grid, and to a lesser extent the backside contact. The conducting media are crucial to the overall efficiency of the cell by providing the means for current to flow when sunlight strikes the doped silicon wafer. This paper presents silver as a vital factor in the PV process, and discusses the future industry requirements as well as a projection for the overall silver market for the next eight years.

Back-sheet materials for photovoltaic modules serve several purposes such as providing electrical insulation, environmental protection and structural support. These functions are essential for modules to be safe for people working near them and for the structures to which they are attached. To ensure that all modules meet a minimum set of requirement, they must pass qualifications tests such as IEC 61646, 61215, 61730, and 62108. This paper puts forward the design and composition requirements of back- and front-sheet materials for achieving the highest possible quality performance from PV modules.

The reliability of United Solar Ovonic (Uni-Solar) triple-junction amorphous-silicon thin-film photovoltaic modules is critical to their success in an increasingly competitive PV market. Modules must show useful operating lifetimes of 20 to 30 years, and although module efficiency is very important, the total energy that a module will produce largely depends on its operating lifetime. Thus, module reliability must be evaluated to estimate lifetime and establish customer warranty periods. While real-world outdoor exposure testing is necessary and important, accelerated environmental test methods must also be utilized to provide more rapid feedback regarding failure modes, design flaws and degradation mechanisms. The following paper gives an overview of the methodology used to ensure long-term reliability of Uni-Solar flexible thin-film modules.

Solar enterprises will each be faced with the occasional surplus or lack of solar modules in their lifetimes. In these instances, it is useful to adjust these stock levels at short notice, thus creating a spot market. Spot markets serve the short-term trade of different products, where the seller is able to permanently or temporarily offset surplus, while buyers are able to access attractive offers on surplus stocks and supplement existing supply arrangements as a last resort.

The costs of a photovoltaic installation are driving the market and the need for subsidized schemes, such as feed-in tariffs. Concentrated photovoltaics (CPV) is leading the development of future lowcost renewable energy sources in two ways: on one hand offering high efficiency systems, and on the other, being most capable of reducing manufacturing costs. The idea to decrease the cost of the photovoltaic system using optical elements to focus the radiation into the cell to reduce the size of the cells has been in the mind of the scientists since the 1970s [1]. But, apart from a reduced market, there were several issues that did not allow CPV success at that time. This paper puts forth the proposition that the key is to replace the area of active material, which is the most expensive, with optic elements, which are well known and cheaper.